Carbon reporting built for collision repair.
Stop chasing carbon data. Start reporting it. Scope 1, 2 & 3 for bodyshops and MSOs across every province, ready when your insurer, OEM or auditor asks.
- Captured automatically via API, OCR or CSV
- Calculated to the GHG Protocol & ISO 14064-1
- Independently verified to ISO 14064-3
- ISO 14064-3 verified
- ISSB
- CSDS
- SBTi
- CDP
1,499tCO2e
22.5%9 mo YTD vs 2025Carbon reporting has moved from optional to expected.
The repair sector is being pulled into decarbonisation by the customers it depends on. Baselining now is far cheaper than scrambling when a tender or an insurer asks.
Insurer & work providers
Insurers and work providers are decarbonising their own value chains and increasingly require their repair networks to report primary Scope 1–3 data, not estimates. Being ready protects the relationship and the volume of work.
ISO 14064, ISSB & CSDS
ISO 14064-1 sets the international rules for quantifying an organisation’s emissions, ISSB S2 and Canada’s CSDS 2 set the climate disclosures your insurer and lenders are moving to, and SBTi defines the science-based reduction pathway. Metimo Auto produces output aligned to all of them from your ledger.
Science-based target deadlines
SBTi carries fixed near-term and 2050 milestones, and you can set your own organisational target on top of that floor. The dashboard plots your reported actuals against both the SBTi pathway and your own pledge, then projects where your current pace lands — so you can see whether you are on or off track while there is still time to act. The longer you wait to baseline, the steeper — and more expensive — the annual cut becomes.
Lower cost, not just lower carbon
Every tonne you cut usually tracks a bill you stop paying — energy, fuel, paint and waste. Baselining now turns decarbonisation into an operational saving, so the work pays for itself rather than sitting as pure compliance cost.
The reporting timeline
2018
ISO 14064-1:2018
Revised international standard for quantifying and reporting organisational emissions.
2021
Net-Zero Accountability Act
Canada writes net zero by 2050 into law, with interim targets along the way.
2023
ISSB S1 & S2
Global baseline for sustainability and climate disclosure, including Scope 3.
2024
CSDS 1 & 2
Canada’s Sustainability Standards Board publishes the Canadian ISSB-aligned standards.
2030 (upcoming)
National 2030 target
Canada aims for 40–45% below 2005 levels, as SBTi near-term milestones fall due.
2050 (upcoming)
Net zero
Canada’s legal deadline and the SBTi long-term backstop for residual emissions.
What a general carbon tool can't do for a bodyshop.
Metimo Auto understands repairs, sites, work providers and the frameworks your customers ask about. Every card below is a real part of the product.
Carbon per repair
Emissions normalised against real throughput, so you can compare centres fairly and keep improving as volumes change. Only a repair-specific platform can measure this.
36.8
kgCO2e per repair12% vs last yearIndependently verified
Our calculation engine is assured to ISO 14064-3, so the numbers you submit stand up to auditors without rework.
ISO14064-3assuredData comes in by itself
Bills, telematics and supplier files are read and tagged automatically, with a data-quality tier on every entry.
gas-bill-oct.pdfOCRNatural gas3.37 tCO2e18,420 kWh · Scope 1 · Primary dataAPIOCRCSVManualGlidepath to net zero
Your pathway is plotted against SBTi to 2050. Drag the slider to see how an extra yearly cut changes where you land.
+1.0%2030 landing 815 t vs SBTi 790 t Behind pathway
Every site in one view
Roll up a whole network, then rank centres by intensity to see which locations move the group number.
- Manchester North29.4 kg/repair
- Bristol Cribbs33.9 kg/repair
- Leeds Ring Road38.5 kg/repair
- Birmingham Central41.2 kg/repair
Alerts before audit time
Flags for missing data, unusual spikes and drift off your glidepath, so issues surface early.
Ask Metimo
Ask questions about your own emissions in plain English. Answers come from your ledger, with the figures behind them, plus a short AI briefing on the Overview each month.
Why did Birmingham Central's gas go up last month?
Gas use was 38% higher than the same month last year, while repairs were up only 6%. Most of the rise is lower efficiency, not more work, so check the booth burner schedule first.
14,210 kWh vs 10,300 kWh412 repairs vs 389Scope 1
Illustrative figures throughout.
From gas bill to signed-off report.
These are the real dashboard charts, running on our demo account. Hover them to read the figures.
- enbridge-gas-oct-2026.pdfToronto EtobicokeReading
- hydro-quebec-oct.pdfLavalReading
- paint-supplier-q3.csvAll sitesReading
- fleet-fuel-card-oct.csvCalgary SouthReading
What's your footprint?
Move the sliders to see a ballpark annual footprint for a network like yours, and how much reporting time you would get back.
170hours a year
saved on carbon reporting compared with spreadsheets.
1,728tCO2e
- Scope 1518 tGas, paint booths, vans
- Scope 2130 tElectricity
- Scope 31,080 tParts, paint, waste, travel
Estimate based on typical bodyshop figures per repair. In Canada the electricity share varies widely by province; your real footprint is calculated from your own bills, suppliers and provincial grid.
Here's how your Overview would look in Metimo Auto
- Gross emissions
- 1,728 t
- Per repair
- 0.240 t
- Repairs a year
- 7,200
- Peak month
- Jan
Monthly split uses typical heating and repair-volume seasonality. Hover a month to read it.
Scope 3 for your repair network, province by province.
Claims repairs are a large part of an insurer's value-chain emissions. Metimo Auto gives Canadian insurers primary data from their approved suppliers, not spend-based estimates, ready for ISSB and CSDS disclosure.
Every province, its own grid
Repairs are calculated with each site’s provincial grid factor, and kWh and m³ of gas are shown alongside tCO2e so a Quebec repair and an Alberta repair can be compared fairly.
One view of the approved network
Insurer staff see read-only repairs and emissions attributed to them, by province, approved supplier and site, with Net Zero progress against their pathway.
Disclosure and board packs
ISSB S2 and CSDS 2 checklists, CSV disclosure packs and a quarterly board pack, emailed to the people who need them.
English and French
The insurer view switches between English and French for teams across Canada.
From a gas bill to a reported number, without a spreadsheet.
Follow one October gas bill through the platform. Scroll through the steps and watch the ledger entry build up beside them.
- Step 1
Bill arrives
Invoices, statements and supplier files land by email forward, upload or API.
gas-bill-oct.pdfBirmingham Central - Step 2
Read automatically
OCR pulls the quantity, unit, period and site, then checks it against last month.
18,420 kWhNatural gas · Oct 2026 - Step 3
Factor applied
The right dated GHG Protocol conversion factor is matched and stamped on the line.
× 0.0360 kgCO2e/kWhOntario NIR grid factor - Step 4
Ledger entry
A traceable entry with a data-quality tier, linked back to the source document.
3.37 tCO2eScope 1 · Primary data - Step 5
Report ready
Totals roll straight into reports, each with a versioned audit trail.
ISSB S2 · CSDS 2 · CDPPlus SBTi tracking
- Source document
- gas-bill-oct.pdf
- Site
- Birmingham Central
- Activity
- —
- Period
- —
- Conversion factor
- —
- Emissions
- —
- Data quality
- —
Illustrative figures.
Where a repair centre's emissions actually come from.
The GHG Protocol sorts every tonne into three scopes. Metimo Auto maps your activity data to the right one automatically, so the split is consistent across every site.
- Suppliers & parts
- Your sites & fleet
- Waste, travel & end of life
- Scope 1On your sites
Direct emissions
Fuel you burn and gases you release from sources you own or control.
- Company vans & courtesy cars
- Spray booth & space-heating gas
- Refrigerant & air-con top-ups
- Scope 2From the grid
Indirect emissions: electricity, heat & steam
Electricity, heat and steam you buy, reported on a location and market basis.
- Grid electricity for lighting & tools
- Renewable tariffs & on-site solar
- Scope 3Across your value chain
Indirect emissions: upstream & downstream
Everything else your business causes, from what you buy to what you throw away.
- Parts, panels & paint purchased
- Inbound deliveries & logistics
- Waste, bumpers & recycling
- Business travel & staff commuting
Same obligation. A completely different amount of pain.
Monthly, not annual.
Measured, not estimated.
All 15 categories, not just a few.
The spreadsheet approach
- A once-a-year spreadsheet scramble
- Recall-based estimates and guesswork
- Generic factors with no data-quality tiering
- Only the easy Scope 3 categories, the rest left blank
- No visibility of supplier engagement or decarbonisation
- Hard to evidence when an auditor asks
- Chasing suppliers and sites by email
- Figures that break under a tender questionnaire
Metimo Auto
- Continuous, always-current emissions data
- Actual activity data captured at source
- Dated GHG Protocol factors on every line
- All 15 Scope 3 categories reported, not just a few
- Supplier engagement and decarbonisation tracked over time
- Every figure traces back to its origin
- Automated collection, connectors and reminders
- ISSB, CSDS & SBTi output ready on demand
Independently verified. Independently certified.
The numbers Metimo Auto produces rest on a methodology that has been checked by an independent verifier, on a platform certified to protect the data behind them.
- Independently verified
The Metimo Auto calculation methodology and dashboard have been independently verified in accordance with ISO 14064-3 to meet the requirements of ISO 14064-1.
- Certified
Metimo Auto is Cyber Essentials certified, the UK Government-backed scheme that confirms the technical controls protecting your data against common cyber threats.
- GHG Protocol & ISO 14064-1
- ISO 14064-3 independently verified
- Cyber Essentials certified
- UK / EU data residency, GDPR-compliant
- Encrypted in transit & at rest
- Versioned, traceable audit trail
- Role-based access control
One plan that scales with your estate.
Billed per organization in Canadian dollars. The platform base includes your first site and founding admin; add sites and users as you grow. Pay 12 months upfront for the price of 10, and invited teammates share the subscription.
or $1,990 paid upfront for 12 months (12 for the price of 10) · includes your first site and founding admin
- Full Scope 1, 2 & 3 inventory
- Carbon intensity metrics & throughput overlays
- Net-zero pathways with glidepath forecasts
- ISSB S2, CSDS 2, CDP & SBTi reporting
- Versioned audit trail & data-quality bands
- Unlimited activity data & reporting years
- Ask Metimo: 100 AI questions a month on your own data
Each additional bodyshop, in any province, rolled into one group view.
Extra seats beyond the founding admin, with role-based access.
Pay a year upfront and the base, sites and users are each charged for 10 months.
The questions repairers ask before they start.
How long does onboarding take?
Most single sites have a first inventory on screen within days — you bring the activity data you already hold (fuel, energy, mileage, spend) and Metimo Auto does the calculation. Multi-site networks are staged site by site, with a shared collection workbook to gather primary data.
Where does my data live and is it secure?
Your data is hosted in the UK/EU, encrypted in transit and at rest, and scoped to your organisation with role-based access. Every input is versioned, so you keep a full, defensible audit trail of who changed what and when.
What if my activity data is messy or incomplete?
Every input carries a data-quality tier with a propagated confidence band, so partial data still produces a usable, honest number. Uploaded invoices are read by OCR and anything below the confidence threshold is queued for human review before it reaches the inventory.
Can I export reports for auditors and tenders?
Yes. Generate ISSB S2, CSDS 2, CDP and SBTi-style reports straight from the ledger, each carrying the data-quality tiering and uncertainty detail assurance providers expect, with every figure traceable to its source activity data and provincial emission factor.
Can you backdate my baseline year with historic data?
Yes. If you hold the activity data for an earlier year — fuel, energy, mileage, waste, spend — we can build a full historic inventory and set that year as your baseline, so your reduction targets and glidepath are measured against where you genuinely started rather than the day you signed up. Historic figures carry the same data-quality tiering and factor traceability as live data, with each year mapped to the correct emission-factor vintage for that period, and once a baseline is set it is version-locked so any later restatement (a boundary change, an improved data source, an acquisition) is recorded transparently and keeps your trend line honest and audit-ready.
Does it work for a single bodyshop and for a large MSO?
Both. Run a single site on the platform base, or roll up an entire group with per-site managers and one consolidated view — then drill into any individual centre to compare performance and carbon intensity per repair.
Ready to put a number on your emissions?
Create your account to start your inventory, or talk to us about onboarding a multi-site network. We are happy to walk through the platform and your reporting obligations.